B&B Electronics Parallel Printer Card PIOC Uživatelský manuál Strana 14
- Strana / 62
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Single Cell Testing
Figure 7. T35-GFX with Single Cell Holder.
If you’re planning on doing a lot of single cell testing, you will want to get a cell holder
from CEI, #CEI -2090. See our website for this and other products.
To use the optional battery box, connect the large alligator clips to the bare 14 gauge
wires on the battery box, (red to red and black to black) or install a high quality connector
of choice. Whatever connector you choose should be rated for continuous current
capacity of 35 amps if you intend to discharge at full rated capability. Then, connect the
small red alligator clip to the small red lead on the cell holder, in like manner, connect the
small black alligator clip to the small black lead. The small voltage leads must be
connected to get accurate discharge readings. DO NOT increase the length of the battery
box high current leads, or introduce any type of additional connection other than the main
connection formed with the end of the leads. To do so may cause discharge current to
taper off at the end of the discharge, due to additional voltage drops introduced by the
additional series resistance.
Mount the end of the battery box with the springs to a flat surface with the holes
provided. The other end of the box is left free to move. Do not tighten the screws all the
way, otherwise the battery box will not move freely.
The battery box may be forced open by squeezing the spring at the end of the rods and
the box between the thumb and the forefingers. This is useful for placing the cell in the
box. The positive terminal of the cell goes to the red lead end of the box. Rotating the cell
back and forth a few times after placing it in the box will insure good connection between
the contacts and the cell. To remove the cell, place your finger underneath the cell and
push up.
14
- Competition Electronics, Inc 1
- Turbo35-GFX 1
- User’s Manual 1
- TABLE OF CONTENTS 2
- Condition your Cells 5
- How to Use this Manual 5
- Prepping the T35-GFX for use 6
- Powering up the T35-GFX 7
- Figure 2. T35 GFX Menu Tree 8
- The Help Line 9
- Loading Factory Setups 10
- Quick Start: Charge 11
- Quick Start: Discharge 11
- Quick Start: Cycle 11
- Quick Start: Motor Run 12
- Single Cell Testing 14
- Actual Internal Resistance 15
- Peak Charge Volts 15
- Discharge Average Volts 15
- Discharge Average Volts at 1V 15
- Run Time 16
- Relative Internal Resistance 16
- Charging 17
- Peak Detect 18
- False Peaking 18
- Cell Heating 18
- Discharging 19
- Figure 10. TurboMatcher 4/35 20
- Extreme Discharge/Equalizing 22
- Superstition 22
- The T35-GFX in Detail 23
- The MODE Button 24
- The PAGE Button 25
- The START/STOP Button 25
- Charge Mode 26
- Charge Rate 27
- Peak Detect Voltage 28
- TurboFlex On/Off 28
- TurboFlex Level 28
- Long Lockout On/Off 28
- # of Peaks 28
- Interpreting the Results 29
- Other Features 29
- Discharge Mode 30
- Discharge Amps 31
- # of Cells 31
- Discharge Profile Mode 31
- Cutoff Voltage 32
- AIR ON/OFF 32
- Cycle Mode 34
- # of Cycles 34
- Cool Down Minutes 34
- Motor Run Mode 34
- Motor Volts 35
- Run Time Minutes 35
- Data Mode 35
- MAN(ual) and AUTO(matic) 36
- GRAPH MAN and GRAPH AUTO 36
- COMP MAN and COMP AUTO 37
- REAL TIME 37
- The Serial Port 37
- Real Time Data Format 38
- Interfacing an ASCII printer 39
- Using the Graphing Features 41
- Data Collection and Storage 42
- Using the Cursor 42
- Setup Mode 42
- Storing/Retrieving Setups 43
- Loading Setups 44
- Saving Setups 44
- Naming/Renaming Setups 45
- Editing Setups 45
- TurboLabel Output 46
- HyperTerminal 48
- Capturing and Saving Data 49
- Tera Term 52
- Then click “Finish” 55
- Open Office 56
- Specifications 57
- When it Doesn’t Work 58
- Figure 23. 20 amp fuses 59
- Firmware Updates 61
- ***Limited Warranty*** 62
Související produkty a manuály pro Sítě B&B Electronics Parallel Printer Card PIOC
Sítě B&B Electronics PES1A Technické informace
(60 stránky)
(60 stránky)
Sítě B&B Electronics SPECTRE Uživatelský manuál
(49 stránky)
(49 stránky)
Sítě B&B Electronics Vlinx MESR9xx Specifikace
(84 stránky)
(84 stránky)
Sítě B&B Electronics ETCIACT Instalační příručka
(10 stránky)
(10 stránky)
Sítě B&B Electronics RS-422 Specifikace
(43 stránky)
(43 stránky)
Sítě B&B Electronics 3PXCC2a Uživatelský manuál
(7 stránky)
(7 stránky)
Sítě B&B Electronics RS-422 Specifikace
(22 stránky)
(22 stránky)
Sítě B&B Electronics DCDSS1 Specifikace
(13 stránky)
(13 stránky)
Sítě B&B Electronics SPECTRE Uživatelský manuál
(2 stránky)
(2 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce